ISIS revolutionized bottom bracket spindles. Keep yours spinning smoothly with this Platinum ISIS Bottom Bracket from FSA. - Forged, hollow chromoly spindle with titanium nitride coating - Integrated, large ball bearing design - Cold-forged aluminum cups - Includes crank bolts

T47 threaded BB cups for running 24mm spindle (Shimano, etc.) cranks in T47 frames. Cups have internal bearings and are typically used in BB shells with widths wider than 73mm. Machined aluminum cups thread together directly into a T47 BB shell. Bearings are easily serviced or replaced. Includes sleeve to fit between cups for added protection from dirt and grime, and also keeps your internal wires and hoses from rubbing on the crank spindle. T47 BB cups are similar to standard BSA threaded cups in that the drive side cup is left-hand thread and the non-drive side cup is right-hand thread. Use a quality grease when installing in steel or aluminum BB shells, or a titanium-compatible anti-seize compound in titanium BB shells. - Bearings: Enduro Angular Contact - Bottom Bracket/Frame Interface: T47 - Bottom Bracket Shell Width: 68mm – 132mm - Bottom Bracket Shell I.D.: 47x1.0mm Threaded - Over Bearing Width: 91.7mm in 86.5mm wide shell (dimensions include supplied silicone dust shields) - Tool Pattern: 48.5mm x 16-notch

Bottom Brackets are an essential part of the bicycle that is often overlooked and forgotten, but we saw the BB as another opportunity for performance gains and improved efficiency. For our BB we have developed a seal that achieves a very low level of drag while still retaining excellent protection qualities. Its thinner and low viscosity bearing grease with the correct fill level offers higher durability at high speeds. If you’re running the best crankset on the market, you should have the performance BB to match. - Thinner and lower viscosity bearing grease for higher durability at high speeds - In-house testing procedure includes developing a 24-hour continuous water invasion test - BB86 41mm Press fit, 30mm Spindle, 66gm, 86.5mm

FSA MegaExo Bottom Bracket - MegaExo cranks to press fit BB89.5 and BB92 frame - Spindle Interface Type: FSA MegaExo - BB Shell Width (mm): 89.5 – 92 - Bottom Bracket Shell I.D.: 41 - BB/Frame Interface: BB89.5, BB92

T47 threaded BB cups for running 22/24mm stepped spindle (SRAM) cranks in T47 frames. Cups have outboard bearings and are typically used in BB shells with widths from 68mm to 100mm. Machined aluminum cups thread together directly into a T47 BB shell. Bearings are easily serviced or replaced. Includes sleeve to fit between cups for added protection from dirt and grime, and also keeps your internal wires and hoses from rubbing on the crank spindle. T47 BB cups are similar to standard BSA threaded cups in that the drive side cup is left-hand thread and the non-drive side cup is right-hand thread. Use a quality grease when installing in steel or aluminum BB shells, or a titanium-compatible anti-seize compound in titanium BB shells. - Bearings: Enduro Angular Contact (22/24mm SRAM non-drive-side bearing: ABEC-3) - Bottom Bracket/Frame Interface: T47 - Bottom Bracket Shell Width: 68mm - 100mm - Bottom Bracket Shell I.D.: 47x1.0mm Threaded - Over Bearing Width: 91.2mm in 68mm wide shell (dimensions include supplied silicone dust shields) - Tool Pattern: 44mm x 16-notch

Campagnolo ProTech bottom brackets feature a patented external sealing ring design that protects a strong, resilient fiberglass-charged polyamide central tube from the harmful ingress of water, mud and grit. - Designed specifically for gravel riding and racing to protect against water, mud & grit

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width, and all CeramicSpeed Bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. You have two bearing choices. The first choice is our low drag, long life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The second choice is our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Compatible with: - Frame: BB86 - Opening diameter: 41mm - Shell width: 86.5mm In the box: - 2 CeramicSpeed Bearings - 2x dust covers - Plast-sheet - 4 x 1mm spacers - 10ml syringe of CeramicSpeed All Round Grease - Sticker Sheet

The Hellbender 70 bottom bracket utilizes a bearing made of 440C stainless steel, providing exceptional ride quality and reliability. The stainless steel bearing in the Hellbender 70 strikes a perfect balance between value and lasting performance. - 440C stainless steel bearings, dual lip seal, marine grease - Machined aluminum cups

The SRAM DUB bottom bracket series has a simple job—connect your crankarms and protect the smooth, long-lasting application of power to your drivetrain. To allow that singular focus, we've engineered the DUB spindle to be the one true unifying component. One oversized spindle to work across every bottom bracket standard. For better crankarm compatibility. For better protection from the elements. For longer-lasting performance. To be stronger, smoother, simpler. Now, back to the ride. - One oversized spindle to work across every bottom bracket standard - Greater bearing durability

The SRAM DUB bottom bracket series has a simple job—to connect crankarms and protect the smooth, long-lasting application of power to the drivetrain. SRAM engineered the oversized DUB spindle to work across every bottom bracket standard, simplifying crankarm compatibility. - Gutter Seal Technology drastically improves sealing against the elements - Sealed cartridge bearings - One oversized spindle to work across every bottom bracket standard

The Hellbender70 bottom bracket utilizes a bearing made of 440C stainless steel, providing exceptional ride quality and reliability. The stainless steel bearing in the Hellbender 70 strikes a perfect balance between value and lasting performance. - 440C stainless steel bearings, dual lip seal, marine grease - Machined aluminum cups

A tough bottom bracket that will go as hard as you. The PowerSpline has a heat-treated chromoly 12 spline spindle to make sure it can go the distance with even the most demanding riders. SPECIFICATIONS: - BB-FRAME INTERFACE: English/BSA 68E/73mm, English/BSA 68mm, English/BSA 73mm - CHAINLINE: 46.0mm, 48.5mm, 51.0mm, n/a - SPINDLE LENGTH: 108mm Spindle, 113mm Spindle, 118mm Spindle - SUPPORT E-TYPE FD: n/a, Yes - CRANK-BB INTERFACE: Power Spline - BEARING TYPE: n/a - SPINDLE DIAMETER: n/a - CUP MATERIAL: n/a - WEIGHT (G): 363 - WEIGHT BASED ON: BSA 73mm, 113mm spindle

The new SRAM DUB bottom bracket series has a simple job: connect your crankarms and protect the smooth, long-lasting application of power to your drivetrain. To allow that singular focus, we've engineered the DUB spindle to be the one true unifying component. One oversized spindle to work across every bottom bracket standard. For better crankarm compatibility. For better protection from the elements. For longer-lasting performance. To be stronger, smoother, simpler. Now, back to the ride. - One oversized spindle to work across every bottom bracket standard. - Greater bearing durability - Easy installation - PressFit cups for lighter weight

Get more distance out of every pedal stroke with SRAM's BB30 Bottom Bracket Assembly. It features sealed bearings for a smooth pedal stroke and impressive reliability. Plus, it presses directly into your frame's BB30 bottom bracket shell for reduced weight and increased longevity.

This bottom bracket is perfect for when you have a PF30, BBright, or 386EVO shell frame and want to install a crank with a 30mm spindle into the frame. All these frame standards have a 46mm inner diameter and smooth insides, though the widths vary from 68mm to 86mm. This bottom bracket features nearly zero loss of power due to friction, thanks to the CeramicSpeed's incredibly efficient bearings. Choose either our Standard or Coated Bearings—both have super-round, super-smooth CeramicSpeed balls rolling on hardened-steel races. The Coated version has a metallic coating laid onto the races, making them even harder and smoother and resulting in longer life and lower drag. They come installed in cups. 30mm spindles on cranks are increasingly popular because of the high stiffness and low weight. 46mm inner diameter bottom brackets are popular for the freedom they offer designers in building frames. Because of the variety of widths, the cups here extend into the shell and come with a telescoping spacer tube to further seal and stiffen the system. The bottom bracket is already stiff thanks to hard ceramic bearings and hardened-steel races. Thanks to CeramicSpeed, it also generates nearly zero drag. Standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction versus conventional BBs. The bearings also last at least 3x longer than other bearings. You can change the grease to fine-tune your BB's performance characteristics. TT and Track, All Round, and LongLife are greases CeramicSpeed designed. The first has the least drag, while the last is the most durable. All Round, in the middle, comes standard in road bearings. In The Box - 2 cups with bearings installed - 2 1mm spacers - 2 0.5mm spacers - 2 dust covers - O-ring - Spacer tube - 10ml All Round Grease - Sticker sheet

The SRAM DUB bottom bracket series has a simple job— to connect crankarms and protect the smooth, long-lasting application of power to the drivetrain. SRAM engineered the oversized DUB spindle to work across every bottom bracket standard, simplifying crankarm compatibility. - Gutter Seal Technology drastically improves sealing against the elements - Sealed cartridge bearings - One oversized spindle to work across every bottom bracket standard - Significantly lighter than GXP system

BSA is another way of stating English threading. The initialization comes from Birmingham Small Arms, which made bicycles. English threading on road bikes mean a 68mm-wide, 34mm-inside-diameter shell with reverse threading on the drive side. It's the most common threaded standard employed today. This kit allows you to fit 30mm cranks, like those from Rotor, to fit in the tight space of this 34mm spindle. Choose between two bearings types for the cups. Standard Bearings have low drag thanks to hardened-steel races and our CeramicSpeed Balls. Coated Bearings have those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Note that the threaded extensions of this BB's cups that thread into the frame are thin, as they need to fit a 30mm spindle inside the cups. CeramicSpeed standard bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction compared to standard bottom brackets. That's thanks to balls that are 100% smoother and 15% harder than the ceramic competition. The bearings last at least 3x longer than other bearings. In The Box: - 2 threaded cups with bearings installed - 2 1mm spacers - 2 0.5mm spacers - 2 dust covers - O-ring - 10ml syringe All Round Grease - Sticker sheet - Spacertube

The Dynatron features an American BB with press fit cups and caged bearings. - Compatible with 1-piece cranks - Frame BB Shell is 68mm width by 51.5mm inner diameter - BB Style: American

The Wheels Mfg BB30 Outboard bottom bracket will give you all of the same benefits as their other Outboard style BBs. The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. Specifically designed for installing 24mm spindle diameter cranks (Shimano, FSA, Etc.) in BB30 frames without the need for adapters. - Bearings: Enduro ABEC-3 - Color: Red - Bottom Bracket/Frame Interface: BB30, Specialized Alloy OSBB - Bottom Bracket Shell Width (mm): 68mm - 73mm - Bottom Bracket Shell I.D.: 42mm - Crank Spindle Type: Shimano Hollowtech II, FSA MegaExo, RaceFace EXI - Crank Spindle Diameter: 24mm - Weight: 130g

Get the most out of SRAM's high-tech cranksets with the GXP Team Bottom Bracket. Built to last, this super-smooth bottom bracket lets your SRAM GXP crankset (sold separately) spin effortlessly without weighing you down.

The Wheels Mfg original PF30 bottom bracket is a significant upgrade to any OEM PF30 bottom bracket. Two machined aluminum cups offer increased durability and bearing life, while keeping a simple press together method for installation and maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. - Bearings: Enduro Ceramic Hybrid - Color: Black - Bottom Bracket/Frame Interface: PF30, BB386EVO, Specialized Carbon OSBB, BBRight" Press Fit - Bottom Bracket Shell Width (mm): 61mm to 86.5mm - Bottom Bracket Shell I.D.: 46mm - Crank Spindle Type: BB30 - Crank Spindle Diameter: 30mm - Weight: 104g

- Simple and reliable square taper bottom bracket - Replaces both BB-UN26 and BB-UN55 - Sealed cartridge bearings - Cr-Mo axle - For bicycles equipped with a chain case, select BB-UN300-K - For E-type front derailleur compatibility, choose BB-UN300-E - Fixing bolts not included; Shimano FC-E6000 bolts suggested

Run 29mm spindle SRAM DUB compatible cranks in a BSA threaded frame. Machined aluminum cups thread into a standard threaded frame and feature Enduro 6806/29 ABEC-3 sealed bearings outboard of the BB shell. Fully serviceable. Bottom Bracket Includes: - BB Cups with bearings - 2 x Silicone dust seals - 2 x 0.5mm crank spindle spacers - 2 x 1.0mm crank spindle spacers - 1 x 2.5mm crank spindle spacer - Bearings: Enduro 6806/29 ABEC-3 - Bottom Bracket/Frame Interface: ISO/English or BSA Threaded (1.37 in x 24 TPI) - Bottom Bracket Shell Width (mm): 68mm, 73mm, 100m - Bottom Bracket Shell I.D.: 33.6-33.9 mm - Crank Spindle Diameter: 29mm - Tool Pattern: 48.5mm x 16-notch - Over Bearing Width: 91.5mm in a 68mm wide shell - Weight: 102g Compatible with the following Bottom Bracket Standards and SRAM DUB compatible cranks with 29mm diameter spindle: - ISO/English or BSA Threaded (1.37 in x 24 TPI) - 68mm, 73mm, and 100mm BB Shell Width (if used in a 100mm wide shell, install the cups without the center plastic center sleeve)

Expand your choice of cranks for use in frames with 41mm ID shells. Replace your bottom bracket with these dual-row flanged bearings and run 29mm spindle (SRAM DUB) cranks in your frame. These bearings fit directly in frames with 41mm ID bottom bracket shells. Crankset spindle length must be longer than 104mm when used in a 86.5mm wide BB shell. - Bearings: Enduro Dual-Row ABEC-3 - Color: Silver - Bottom Bracket/Frame Interface: BB86, BB92, PF90, BB104/107, PF121, PF132 - Bottom Bracket Shell Width: 86.5mm - 132mm - Bottom Bracket Shell I.D.: 41mm - Flange OD: 42mm - Crank Spindle Diameter: 29mm (DUB) - Over Bearing Width: 92mm in 86.5mm wide shell (Dimensions include supplied silicone dust shields) - Weight: 90g Complete kit for one frame includes: - (2) Enduro BB86 to 30MM Dual-Row ABEC-3 Bearing - (2) 0.5mm crank spacer - (2) 1.0mm crank spacer - (2) 5.0mm crank spacer - (2) Dust seals

- Compatible with both American and Mid style BB shells - 6061-T6 full CNC alloy construction - Anodized surface finish - Weight: 255g - Cup Type: Press Fit - Cup OD/Bearing OD: 41mm or 51mm

Rock The BB Precise fit, smooth-rolling operation, long-living performance–what more can you ask for from a bottom bracket? Install a 30mm CINCH crankset friendly PF30 and get riding...and keep riding. Rolling deep The PF30 bottom bracket uses reliable 6806 retainer bearings packed with waterproof grease, along with wiper seals to keep the gunk out. Close Enough Won't Cut It We fired up the ol' CNC machine to make sure the anodized 30mm alloy cups of this bottom bracket provide an exact, perfectly quiet fit for your frame. Weather, Or Not All RF bottom brackets come with an inner plastic sleeve to keep the elements out and the appropriate spacers to ensure a perfect fit.

The BB86 mountain bike standard was designed to integrate bearings into the bottom bracket for weight reduction. This kit works with the standard: it consists of two cups that are pressed into either side of the shell. There are two versions of this bottom bracket. Both come with CeramicSpeed Bearings installed into cups. The first is our long-life, low-drag Standard Bearing with hardened-steel races and our CeramicSpeed super-round, super hard balls. The second is our Coated bearing, which uses those same CeramicSpeed Balls installed on coated, hardened-steel races for longer life and less bearing drag. This CeramicSpeed BB86 Bottom Bracket meshes with cranks that have 24mm spindles, including both Shimano and FSA. CeramicSpeed standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That means an average 75% drag reduction compared to standard bottom brackets. The hardened-steel races feature CeramicSpeed Balls that are 100% smoother and 15% harder than the ceramic competition. The CeramicSpeed Bearings last at least three times longer than other bearings. Coated Bearings drop friction further and increase lifespan to applying a coating to the races. The coated races see a 50% drag reduction and an improvement in bearing life of 60%. In The Box - 2 bottom bracket cups with bearings installed - 2 dust covers with integrated spacers installed - Spacer tube - 10ml syringe of LongLife Grease - Sticker sheet

The EVO386 standard is designed for oversized spindles. CeramicSpeed's kit for Shimano allows you to install Shimano or FSA cranks with 24mm spindles. The cups come with CeramicSpeed Bearings installed. Both CeramicSpeed Standard and Coated Bearings are available. Both utilize super smooth CeramicSpeed Balls and hardened-steel races. The latter has an additional metallic coating on the races to further smooth and harden the steel, further increasing life and lowering drag. The design of overlapping cups extending through the shell for EVO386 reduce the likelihood of creaking and increase the reliability of the system. The CeramicSpeed Standard Bearings feature an average drag reduction of 75% compared to stock bottom brackets. That translates into frictional drag of 0.3-0.4 watts per set, which is the result of great design, hardened-steel races, and ceramic balls that are 100% smoother and 15% harder than the ceramic competition. The CeramicSpeed Coated Bearings are a step up as they reduce drag by 50% compared to our Standard Bearings and an improvement in bearing life by 60%. All Round Grease comes standard in the bearings, but can be replaced for lower drag TT and Track Grease or higher durability LongLife Grease, which adds a bit of drag but stays in the bearing when riding through messy conditions. In The Box: - 1 bottom bracket with bearings installed - 2 dust covers - 10ml syringe of All Round Grease - Sticker Sheet

The PF30 standard has opened design possibilities for mountain bikes. Our CeramicSpeed PF30 Shimano MTB Bottom Bracket gives you the ability to install Shimano and other 24mm diameter spindle cranks on your PF30 MTB. Our PF30 cups have extended sleeves and join with a center section, reducing the likelihood of creaking and increasing the reliability of the system. There is both a Standard and Coated version. Both feature super smooth CeramicSpeed Balls and hardened-steel races. The CeramicSpeed Coated Bearings have an additional benefit: a 3-micron thick metallic layer over the races. This addition makes the races harder and smoother, lowering drag and increasing life. The CeramicSpeed Standard Bearings have only 0.3-0.4 watts of frictional drag per set, an average drag reduction of 75% compared to stock bottom brackets. This is the result of great design, including hardened-steel races and CeramicSpeed Balls that are 100% smoother and 15% harder than the ceramic competition. They also last longer. If you want longer life and even lower drag, opt for the CeramicSpeed Coated Bearings. Life increases by 60% and drag drops by 50% compared to our CeramicSpeed Standard Bearings. Performance can be tuned by changing the grease. LongLife Grease comes installed, but can be changed for lower-drag All Round Grease for lower drag and cleaner riding conditions. In The Box - 1 bottom bracket with CeramicSpeed bearings installed - 2 dust covers - 5 0.85mm spacers - 10ml syringe of LongLife Grease - Sticker sheet

Race Face bottom bracket spacer kit for 124-130mm bottom brackets.

The Wheels Mfg PF30 Outboard bottom bracket will give you all of the same benefits as their well-loved Outboard style BBs. The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. Specifically designed for installing 24mm spindle diameter cranks (Shimano, FSA, Etc.) in PF30 frames without the need for adapters. - Bearings: Enduro ABEC-3 - Color: Red - Bottom Bracket/Frame Interface: PF30, Specialized Carbon OSBB - Bottom Bracket Shell Width (mm): 68mm - 73mm - Bottom Bracket Shell I.D.: 46mm - Crank Spindle Type: Shimano Hollowtech II, FSA MegaExo, RaceFace EXI - Crank Spindle Diameter: 24mm - Weight: 161g

Wheels Manufacturing's PressFit 30 Bottom Brackets are an excellent direct replacement for SRAM, FSA and other PressFit 30 BBs. They are 100% made in the USA with machined aluminum cups for superior durability and your choice of standard sealed, angular contact or ceramic bearings (this model has sealed bearings). Wheels Manufacturing also exclusively uses Enduro bearings for excellent performance and longevity. Other great features of these stellar BBs include a 12% increase in bearing strength over standard models; serviceable bearings; dual exterior silicone rings for easy installation and to eliminate creaking; double-lip bearing seals; and even the highest quality grease appropriate for bottom bracket use and also more of it for smoother running and maximum durability!

Surly OD Bottom Brackets - PF cups are 41mm in diameter - Bearing I.D. is 24mm - OD bottom bracket comes with telescoping center sleeve for added durability - High quality double labyrinth sealed stainless Enduro bearings with corrosion resistant coating - 3 additional 1mm spacers are provided to help with chain line and crank arm clearance

BBright is the Cervelo bottom bracket standard found on most of their frames, save the P5. In order to fit Shimano and FSA cranks into this oversized shell, this bottom bracket, complete with CeramicSpeed Bearings, needs to be pressed in. The BBright bottom bracket comes with either CeramicSpeed Standard or Coated Bearings installed. Super smooth, super-round CeramicSpeed Balls contained in hardened-steel races are found on both versions. The Coated version has a metallic coating laid onto the races, making it even smoother and harder, resulting in lower drag and longer life. BBright is similar to BB30, but is wider on the non-drive side. As such, the bottom bracket for running 24mm diameter cranks from Shimano, FSA, and others, is unique. The CeramicSpeed Standard Bearings last at least three times longer than other bearings. Thanks goes to hardened-steel races and CeramicSpeed Balls that are 100% smoother and 15% harder than the ceramic competition. These have a frictional drag of 0.3-0.4 watts per set, which represents an average 75% drag reduction compared to most BBs. The CeramicSpeed Coated Bearings reduce drag by 50% compared to CeramicSpeed Standard Bearings, and show an improvement in bearing life by 60%. In The Box - 1 bottom bracket with bearings installed - 2 dust covers - 10ml syringe of All Round Grease - Sticker sheet

- Simple and reliable square taper bottom bracket - Replaces both BB-UN26 and BB-UN55 - Sealed cartridge bearings - Cr-Mo axle - For bicycles equipped with a chain case, select BB-UN300-K - For E-type front derailleur compatibility, choose BB-UN300-E - Fixing bolts not included; Shimano FC-E6000 bolts suggested

Tech specs: - BSA: 91g - PF30: 117g - BB86: 66g - BB386: 103g

BB90 is the Trek oversized bottom bracket standard and is only found on Trek road bikes. The shell is 90.5mm wide and is designed to work with 24mm spindles and road cranks and have the bearings inside the shell. The CeramicSpeed Bearings come as two bearings, which are then pressed into the frame. Those two bearings consist of either CeramicSpeed Standard or Coated Bearings. Both feature super smooth, super-round CeramicSpeed Balls contained in hardened-steel races. The Coated version has a metallic coating laid onto the races, making it even smoother and harder, resulting in lower drag and longer life. -BB90 is simple and light. The standard is designed to work with 24mm spindles. The bearings work with Shimano and other 24mm cranks, like FSA. - The CeramicSpeed Standard Bearings last at least 3 times longer than other bearings. That's thanks to hardened-steel races and CeramicSpeed Balls that are 100% smoother & 15% harder than the ceramic competition. These bearings have a frictional drag of 0.3-0.4 watts per set, which represents an average 75% drag reduction compared to stock BBs. - The CeramicSpeed Coated Bearings reduce drag by 50% compared to Standard Bearings and an improvement in bearing life of 60%. In The Box: - 2 BB90 bearings - 2 seals - 2 dust covers with integrated spacers - 10ml syringe of All Round Grease - Sticker Sheet

- Converts a threaded Euro style bottom bracket to accept MID style 19mm compatible cranks - Bearings included - Shell: Euro - Interface: English - Spindle Type: 19mm - Cup Material: Alloy

The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life and simplifying maintenance. Enjoy smooth operation, fast bearing replacement, and no more creaking. - Bearings: Enduro Angular Contact - Color: Black - Bottom Bracket/Frame Interface: Cannondale BB30A - Bottom Bracket Shell Width: 73mm - Bottom Bracket Shell I.D: 42mm - Over Bearing Width: 91mm in 73mm wide shell (dimensions include supplied silicone dust shields) - Tool Pattern: 44mm x 16 notch

Run your 386EVO crank with your frame that is designed for BB86 Shimano Pressfit bottom brackets with this FSA bottom bracket. - 2 lines of bearings on each side

Threaded Angular Contact BB for 386EVO frames (86.5mm shell width, 46mm shell ID). Machined cups thread together for stability, increased bearing life, and simple installation and maintenance. No more creaking. Smooth operation. Fast bearing replacement. - Bearings: Enduro Angular Contact - Color: Black - Bottom Bracket/Frame Interface: BB386EVO - Bottom Bracket Shell Width (mm): 86.5mm - Bottom Bracket Shell I.D.: 46mm - Crank Spindle Type: BB30 - Crank Spindle Diameter: 30mm - Weight: 124g - Packaged for retail display - Will accept 24mm and 24/22mm cranksets using Wheels Mfg. 386EVO BB / Crank Adapters

Wheels Mfg original BB86/92 bottom bracket is a significant upgrade to any OEM BB86 bottom bracket. Two machined aluminum cups offer increased durability and bearing life, while keeping a simple press together method for installation and maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. - Bearings: Enduro ABEC-3 - Color: Red - Bottom Bracket/Frame Interface: BB86, BB92 - Bottom Bracket Shell Width (mm): 86mm - 92mm - Bottom Bracket Shell I.D.: 41mm - Crank Spindle Type: GXP (SRAM, Truvativ, Etc.) - Crank Spindle Diameter: 22/24mm - Weight: 114g

External English (BSA) threaded road bottom bracket for 68mm shells. Wheels Mfg uses only Enduro bearings and silicone seals for the most durable and smoothest bottom brackets available. Fully serviceable. Includes: (2) - Enduro Silicone dust seals (1) - 2.5mm aluminum BB cup spacer (2) - 0.5mm crank spindle spacers (2) - 1.0mm crank spindle spacers Direct replacement for SRAM/Truvativ GXP bottom brackets! - Bearings: Enduro ABEC-3 - Color: Gray - Bottom Bracket/Frame Interface: ISO/English or BSA Threaded (1.37 in x 24 TPI) - Bottom Bracket Shell Width (mm): 68mm - Bottom Bracket Shell I.D.: 33.6-33.9 mm - Crank Spindle Type: GXP (SRAM, Truvativ, Etc.) - Crank Spindle Diameter: 22/24mm - Weight: 111g

External English (BSA) threaded bottom bracket for 73mm shells. Wheels Mfg uses only Enduro bearings and silicone seals for the most durable and smoothest bottom brackets available. Fully serviceable. Includes: (2) - Enduro Silicone dust seals (1) - 2.5mm aluminum BB cup spacers for use with 68mm wide BB shell (1) - 1.8mm aluminum BB cup spacers for use with 68mm wide BB shell (1) - 0.7mm aluminum BB cup spacers for use with 68mm wide BB shell (2) - 0.5mm crank spindle spacers (2) - 1.0mm crank spindle spacers (1) - Wave Washer Direct replacement for SRAM/Truvativ GXP bottom brackets! - Bearings: Enduro Angular Contact - Color: Red - Bottom Bracket/Frame Interface: ISO/English or BSA Threaded (1.37 in x 24 TPI) - Bottom Bracket Shell Width (mm): 68-73mm - Bottom Bracket Shell I.D.: 33.6-33.9 mm - Crank Spindle Type: GXP (SRAM, Truvativ, Etc.) - Crank Spindle Diameter: 22/24mm - Weight: 116g

- Converts a 68mm American style bottom bracket to take a 3-piece 19mm-spindle crank - Bearings included - Shell: 68mm - Interface: American - Spindle Type: 19mm - Cup Material: Alloy

Designed to be used with X-Type or EXI cranksets. Manufactured from high strength aluminum & featuring custom retainer bearings. Features • BB Cups are forged & CNC machined from 6066 aluminum. • Tapering wall construction to minimize weight. • Custom 6805 16 ball retainer bearing • Bearings feature our custom triple wiper seal to better retain grease & keep contaminants out. • Bearings are factory filled with Phil Wood waterproof grease — tested & proven to extend bearing life.

Expand your choice of cranks for use in BB86/BB92/BB91/BB71-41/BB107 frames. Replace your bottom bracket with these dual-row flanged bearings and run 30mm spindle cranks (FSA BB386EVO, Rotor 3d+, RaceFace Next SL, e.thirteen) cranks in your frame. These bearings fit directly in frames with 41mm ID smooth bore bottom bracket shells.You must use 30mm spindle cranksets with spindle lengths longer than 104mm. - Bearings: Enduro Dual-Row ABEC-3 - Dimensions: 41mm x 30mm (42mm flange OD) - Color: silver - Bottom Bracket/Frame Interface: BB86, BB92, BB91, BB71-41, BB107/104 - Bottom Bracket Shell Width (mm): 86.5mm - 107mm - Bottom Bracket Shell I.D.: 41mm - Crank Spindle Type: BB386EVO, BB30 longer than 104mm - Crank Spindle Diameter: 30mm - Weight: 89g

Origin-8's ISIS Bottom Bracket is everything you need to get your wheels rolling. It features a steel body and hollow-chromoly spindle that adds stiffness and cuts down on weight. The sealed bearings are super smooth and durable, and this fine BB is available in 3 sizes with a 68mm shell.

Forged and CNC machined AL6061 cups - Double sealed replaceable bearings - Fits 68mm and 73mm shell widths - 1.37" x 24T English thread - Alloy spacers included for chainline adjustment - Anodized and laser etched finish

- Thread-together bottom brackets provide a secure and stable shell interface for smoother operation and extended bearing life - OS versions are designed for use in frames with worn-out, oversized bottom bracket shells - Hybrid AL6061/Nylon fiber cups for a superior fit and noise free operation - Low-friction dual seals protect the bearings from harmful contaminants - Sealed premium bearings are both serviceable and replaceable - Models available for both Shimano HTII 24mm and SRAM GXP 22/24mm spindles - Replaces all standard BB86/92 press-fit bottom brackets - Origin8 Nylon composite BB tools are recommended to avoid the possibility of damaging the cups

Race Face SRX ISIS bottom brackets feature 6061-T6 aluminum cups, high-pressure axle seals, adjustable chainline and M15 spindles. • Features 6061-T6 aluminum cups, high-pressure axle seals, adjustable chainline and M15 spindles • Requires ISIS installation tool

T47 threaded BB cups for T47 frames and 30mm diameter spindle cranks. Cups have internal bearings, and can be used in BB shells with widths from 68mm to 132mm. Machined aluminum cups thread together directly into a T47 BB shell. Bearings are easily serviced or replaced. Includes sleeve to fit between cups for added protection from dirt and grime, and also keeps your internal wires and hoses from rubbing on the crank spindle. T47 BB cups are similar to standard BSA threaded cups in that the drive side cup is left-hand thread and the non-drive side cup is right-hand thread. Use a quality grease when installing in steel or aluminum BB shells, and an anti-seize compound compatible with titanium BB shells. Bottom Bracket Includes: - BB Cups with bearings - 2x Silicone dust seals - 2x 0.5mm crank spindle spacers - 2x 1.0mm crank spindle spacers Specifications: - Bearings: Enduro ABEC-3 - Bottom Bracket/Frame Interface: T47 - Bottom Bracket Shell Width (mm): 68mm - 132mm - Bottom Bracket Shell I.D.: 47x1.0mm Threaded - Crank Spindle Diameter: 30mm - Over Bearing Width: 68mm in 68mm wide shell - Over Bearing Width Dimensions include supplied silicone dust shields - Tool Pattern: 48.5mm x 16-notch - Weight: 97g

Box Two Square Taper Chromoly Bottom Brackets are the best option for young BMX racers and other users of three-piece cranks in search of an affordable, high-performance square taper bottom bracket. Each bottom bracket is hand-assembled with a Chromoly spindle, sealed bearings, forged and CNC-machined alloy cups, and a composite center spacer/seal. Features: - Precision Abec-5 Sealed Bearings Compatibility: - Box Five Square Taper Crankset Specs: - Process: CNC-Machined Cups Material: - Spindle: Chromoly - Cups - Alloy - Sleeve - ABS Plastic - Finish: Nickel Coating - Spindle Type: JIS Square Taper - Spindle Length: 108mm or 113mm - Shell Width: 68mm - Thread: 1.37" x 24 TPI - Compatibility: BSA Threaded - Weight [108-113] (+/- 5%): 272 g / 9.6 oz

- Bottom bracket for one-piece crank - Sealed mechanism - 24 TPI - Spindle Type: One piece - Cup Material: Steel - Weight: 310-315g - Cup Type: Press Fit - Cup OD/Bearing OD: 51mm

BBRight™ Outboard bottom bracket for use with 24mm spindle diameter cranksets. The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. - Bearings: Enduro ABEC-3 - Color: Black - Bottom Bracket/Frame Interface: BBRight™ Press Fit - Bottom Bracket Shell Width (mm): 79mm - Bottom Bracket Shell I.D.: 46mm - Crank Spindle Type: Shimano Hollowtech II, FSA MegaExo, RaceFace EXI - Crank Spindle Diameter: 24mm - Weight: 148g

By popular demand, Wheels Mfg. added this PF30 Outboard Bearing BB for use with 29mm spindle SRAM DUB cranksets when used in PF30 frames. The two machined aluminum cups thread together keeping the bottom bracket stable in the frame, increasing bearing life and simplifying maintenance. Enjoy smooth operation, fast bearing replacement, and no more creaking. - Bearings: Enduro ABEC-3 - Color: Black - Bottom Bracket/Frame Interface: PF30, Specialized Carbon OSBB - Bottom Bracket Shell Width: 61mm – 73mm (Specialized Carbon OSBB with 61mm shell width will need additional 3.5mm cup spacers, sold separately) - Bottom Bracket Shell I.D.: 46mm - Over Bearing Width: 89mm in 68mm wide shell (dimensions include supplied silicone dust shields) - Crank Spindle Diameter: 29mm - Tool Pattern: 48.5mm x 16 notch - Weight: 156g

Spinning and Grinning This rock-solid, durable performer is everything you need in a press-fit 24mm bottom bracket and nothing more. Roll on...and on...and on. In A Sea Of Bearings These little buggers can make a huge difference, so we've made sure our double row custom retainer bearings are super durable and up for the long run. Close Enough Won't Cut It These precision steel cup are coated for corrosion resistance, and CNC-ground surfaces of this bottom bracket provide an exact, perfectly quiet fit in your frame. Weather, Or Not All RF bottom brackets come with an inner plastic sleeve to keep the elements out and include all appropriate spacers to ensure a versatile fit.

BSA Bottom Bracket

The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life and simplifying maintenance. Enjoy smooth operation, fast bearing replacement, and no more creaking. - Bearings: Enduro ABEC-3 - Color: Black - Bottom Bracket/Frame Interface: Cannondale BB30A - Bottom Bracket Shell Width: 73mm - Bottom Bracket Shell I.D.: 42mm - Over Bearing Width: 91mm in 73mm wide shell (dimensions include supplied silicone dust shields) - Tool Pattern: 44mm x 16 notch

Wheels Mfg solution for running a 30mm spindle crankset in a BSA threaded frame. Machined aluminum cups thread in to a standard threaded frame and feature Enduro 6806 ABEC-3 sealed bearings outboard of the BB shell. Fully serviceable. Notes: - For use with BB30 Wide 30mm diameter cranks with a spindle length of at least 104mm. - Will not work with standard BB30 cranksets. PLEASE MEASURE YOUR BB30 CRANK SPINDLE LENGTH! - Use only bottom bracket tools compatible with 16-notch MegoEvo BB’s. (FSA MegaEvo and Park Tool BBT-29). - Bearings: Enduro Angular Contact - Color: Black - Bottom Bracket/Frame Interface: ISO/English or BSA Threaded (1.37 in x 24 TPI) - Bottom Bracket Shell Width (mm): 68mm - Bottom Bracket Shell I.D.: 33.6-33.9 mm - Crank Spindle Type: BB30 Wide, BB30a, 386EVO, Rotor 3D+, SRAM BB30 Wide - Crank Spindle Diameter: 30mm - Crank Spindle Length: At least 104mm - Weight: 100g